Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateFast, Reliable Garage Door Repair Across Burbank
Garage door repair in Burbank typically runs $150 to $600, with spring jobs landing between $180 and $340. Most calls we take from Burbank homeowners get same-day or next-day service because we keep trucks stocked and routes built around the Valley. If your door won’t open, grinds on the track, or sags on one side, call (855) 684-6988 and we’ll diagnose it straight.
We work throughout Burbank, from the 91505 flats near Magnolia Park up through the 91506 and 91507 hillside streets above Glenoaks. Our techs know the difference between a 1920s tilt-up wood door in the Rancho district and a 1960s ranch-style sectional near the airport, because those doors fail differently and need different parts. We’re a specialist shop, not a general handyman service. Garage doors are all we touch.
Why All Star Garage Door Co Is Burbank’s Preferred Garage Door Repair Company
Burbank homeowners call us because we show up knowing the door. We have worked on garages all over Burbank, from tight single-car openings in Magnolia Park to wide two-car hillside setups above Glenoaks. That local reps matter when a door binds on a low header or a spring snaps on an oversized panel. We have seen it before and we know what it costs to fix before we pull up.
We specialize exclusively in garage doors. It’s all we do, and we do it at an All Star level. Our Garage Door Repair team carries multi-brand parts on the truck, so a Chamberlain or Genie opener gets serviced the same trip as a Clopay or Amarr door. Whatever brand is on your door or opener, we know it. The right fix, not the most expensive one.
Troy Winslow built All Star Garage Door Co around a simple standard: field techs who can diagnose across brands and finish the job in one visit. That matters in Burbank, where houses are old, garages are undersized, and homeowners work studio hours that don’t allow for a second appointment. From a broken spring to a full new door, one call covers it.
Styles & brands we work with
Garage Door Spring Repair in Burbank
Garage Door Spring Repair in Burbank is the most common job we run, and for good reason. The Valley’s hot, dry air and Santa Ana wind cycles put constant stress on torsion springs, especially on heavier two-car doors and detached workshop doors. A spring that snaps under load leaves the door dead on the floor, and Burbank homeowners call it in at 6 a.m. on a workday. The job costs $180 to $340 in Burbank, depending on spring weight and cycle rating.
Torsion Spring Cycles and Valley Heat
Most stock springs are rated for 10,000 cycles, which translates to about 7 to 10 years of normal use. But Burbank’s heat accelerates metal fatigue, and heavier hillside doors burn through cycles faster. We stock high-cycle torsion springs for exactly this reason. If your spring snapped after only a few years, the fix is usually a stronger spring, not the same one.
Low-Headroom Torsion Systems
Burbank’s pre-war bungalows often have single-car garages with low headers that a standard torsion setup won’t clear. We spec low-headroom torsion systems for these openings. It costs a little more than a standard spring swap, but it is the correct fix, and it keeps the door lifting smoothly without chewing through cables.
Garage Door Sensor Repair in Burbank
Garage Door Sensor Repair in Burbank is a close second behind springs, especially on 91505 and 91506 homes where garage doors sit inches from the sidewalk or face direct afternoon sun. Photo-eye sensors get knocked out of alignment, caked with Valley dust, or baked by heat reflecting off stucco and pavement. When the sensors misalign, the opener reverses and refuses to close. Sensor repair runs $120 to $240 in Burbank, and it is one of the fastest fixes we do.
Why Burbank Sensors Trip So Often
Two things hit Burbank sensors harder than most: sun glare and dust. West-facing openings in the 91505 flats catch direct afternoon glare that can blind a sensor, and the dry Valley air keeps fine dust in suspension that settles on the lenses. We calibrate sensors with the door in the closed position, then test obstruction reversal in direct sunlight. If a sensor keeps tripping after alignment, we replace it rather than leave a door that reverses unpredictably.
Sensor Wiring and Old Openers
Many Burbank homes still run Chamberlain or Genie openers from the 1990s and early 2000s. Their sensor wiring frays behind the track after decades of door vibration. We will solder or replace the wire rather than tell you to buy a new opener, unless the opener itself is failing. Brand-agnostic service means exactly that: we fix what you own.
Trusted Brands We Service in Burbank
We train on and service Chamberlain, Genie, Clopay, and Amarr equipment, which covers most of what is installed across Burbank. When a Magnolia Park bungalow needs a new sectional door for a low-header opening, we are usually spec’ing an Amarr or Clopay panel with a Chamberlain opener. When a hillside workshop door breaks a spring, we match the torsion setup to the existing door brand rather than ripping everything out. We stock parts for Burbank customers so most repairs finish the same trip.
Common Garage Door Repair Problems We See in Burbank Homes
- Warped one-piece tilt-up wood doors. Original doors on 1920s to 1950s bungalows dry-crack under Valley sun, then bind on their lightweight hardware and strain the opener. The fix is usually a sectional conversion, not another season of patching.
- Low headers on Magnolia Park single-car garages. A standard 7-foot sectional will not fit under many pre-war headers. We reframe or install low-headroom torsion systems that keep the door street-legal and working smoothly.
- Heavy double doors on hillside and workshop garages. Oversized panels ride heavier than suburban single doors, which chews through standard springs fast. Burbank hillside homes need higher-cycle torsion springs or they will be replacing them every few years.
- Sensor misalignment from heat and glare. West-facing doors in the 91505 and 91506 flats catch direct afternoon sun that trips photo-eye sensors. We calibrate and shade sensors so the door closes on command, not after three tries.
See the difference
Before
After
Before
After
Before
AfterPricing for Garage Door Repair in Burbank, CA
Garage door repair in Burbank runs $150 to $600 on average, and we quote the full price before any work starts. You will know the number before we touch a wrench. Here is the line-item breakdown for Burbank:
| Service | Typical Burbank Price |
|---|---|
| Garage Door Repair | $150 – $600 |
| Spring Repair | $180 – $340 |
| Cable Repair | $130 – $250 |
| Opener Repair | $120 – $320 |
| Track Realignment | $120 – $240 |
| Panel Replacement | $250 – $500 |
What moves the price is spring weight and cycle rating, door size, and whether a low-header situation needs reframing. We do not quote a low number and then pad the invoice. The price we quote on the phone is the price you pay, and estimates are free. Call (855) 684-6988 to get yours.
A Burbank Job You Might Recognize
We got a call from a Magnolia Park homeowner whose original one-piece tilt-up wood door had finally warped past saving in the Valley heat. The low header on that 1920s single-car garage would not take a stock sectional door. Our tech reframed the opening, spec’d a low-headroom torsion spring setup rated for higher spring cycles, and set new photo-eye sensors on a LiftMaster opener, all in one trip so the homeowner wasn’t left with an open garage overnight. The door now seals tight against the Santa Ana gusts and clears the low header with room to spare. That is the job we do regularly in Burbank.
This is the All Star difference in Burbank: we spec for the actual door, opening, and climate, not for a generic suburban garage. Magnolia Park and the Rancho district have garages that a neighboring Valley city would never produce. We know that before we pull into your driveway.
We Also Serve Cities Near Burbank
Our Burbank crew covers neighboring Universal City, North Hollywood, Glendale, and Studio City too. If your door breaks at the studio lot exit or the house up the hill, we are already in the area. Call the same number, (855) 684-6988, and we will route the nearest truck.
Serving Burbank, CA — Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Garage Door Repair in Burbank
Yes, but it usually means reframing the opening or installing a low-headroom torsion system rather than a straight swap. We do both in Burbank. The cost depends on whether you need reframing; a low-headroom torsion setup alone runs roughly $250 to $340, while reframing adds to the job. Call (855) 684-6988 and we will measure the header and give you a written price.
A double garage door typically weighs 250 to 450 pounds, and a heavier door needs springs matched to its weight, not a universal size. Undersized springs break early, which is why Burbank hillside and workshop doors need higher-cycle torsion springs. We spec spring weight and cycle rating to the actual door on the truck and complete most spring jobs in one visit.
Most cracked Burbank tilt-up wood doors are past repair, because the wood has dried through and will not hold fasteners. Replacement with a sectional door runs $700 to $2,200 depending on size and whether the low header needs reframing. It is a one-day job, and we quote the full price before starting.
Yes, we keep high-cycle torsion springs on our trucks for Burbank’s heavier doors, including hillside two-car garages and detached workshops. Standard 10,000-cycle springs fail early under those loads; high-cycle springs are rated for up to 30,000 cycles or more. You will pay a little more, but the door will not snap a spring in three years.
Yes, Burbank’s west-facing garages in the 91505 and 91506 flats catch direct afternoon sun that can blind photo-eye sensors, and dry Valley dust builds up on the lenses. We clean, realign, and test sensors in direct sunlight, and if the sensor keeps failing we replace it. Sensor repair runs $120 to $240 in Burbank.
If your garage door is giving you trouble in Burbank, call All Star Garage Door Co at (855) 684-6988. We’ll quote the job before any work starts, and we’ll fix the right thing the first trip.
Written by Troy Winslow, Owner at All Star Garage Door Co, serving Burbank and the San Fernando Valley.